WARNING!
Printed in U.S.A.
1) Do: Check tightness of hose nut to be sure hose is securely attached to the
tank outlet.
2)Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of
these conditions are found, replace hose before using. Replace with original
manufacturer’s parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions),
inspect interior and exterior of tank for signs of deterioration of body and
bottom. Any sign of deterioration indicates possible tank weakening and could
result in explosive bursting under pressure. If any of these signs are found,
discard tank immediately and replace. Do not attempt to patch leaks, etc., as
this could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water
only.
5) Do: Pump plunger 8-10 strokes and inspect for leaks.
6) Do: Direct shut-off away from you and open to make sure discharge is not
clogged.
7) Do: If unit passes this test, release pressure (see Pressure Releasing Instruc
tions), empty tank, and proceed with Filling, Pressurizing and Spraying
Instructions.
3. Pre-Use Check
4. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings
on chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: over
fill to accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel.
Replace pump in tank and tighten securely.
5. Pressurizing and Spraying
Do: Turn handle
clockwise to tighten.
Push handle down,
turn 1/4 turn counter-
clockwise to release.
Do: Pump until
you feel resis-
tance.
Do: Push handle,
down, turn 1/4 turn
clockwise to lock.
Begin spraying.
Re-pump sprayer as
required to maintain
spray force.
6. To Release Pressure
1) Your sprayer is equipped with a pressure relief/release
valve. To release pressure lift and hold the cap until
air is completely exhausted, OR, turn the valve slowly
counterclockwise until you hear air escaping and wait
air is completely exhausted.
2) Do: Stay away from the sprayer until all air has
escaped.
7. Care, Storage and Maintenance
1) Do: Rinse tank thoroughly with water only, empty, refill with water.
Follow Filling, Pressurizing and Spraying Instructions, except pump unit
only 8-10 strokes.
2) Do: Open shut-off and allow water to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove
pump and empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry
location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down
pump rod through opening in cover.
010963 (A) R0000
5A
5C
1. Hose to Tank
5B
Make sure white
outlet tube is
attached to hose.
Insert tube
into tank.
Parts
6-5943
Nozzle
301219
Shut-off
6-7711
Extension wand
301515
Pump
Assembly
P.O. Box 549 700 Ellicott St.
Batavia, NY 14021-0549 U.S.A.
1-800-950-4458 www.chapinmfg.com
WARNING: Handling the brass parts
of this product will expose you to lead,
a chemical known to the State of Cali-
fornia to cause birth defects and other
reproductive harm. Wash hands after
handling.
6-5797
Nozzle
2. Nozzle
Attach nozzle to shut-off handle or extension wand.
1A 1B
Proper place-
ment of white
outlet tube.
1C
Line up tabs on safety
lock connector with
notches on the outlet
flange of the tank.
Insert tabs into notches
to form a secure seal.
4
1D
Slip hose nut down
to tank, turnclock-
wise and tighten as
tight as possible by
hand.
1E
Hazard: Improper use or failure to follow instructions can result in explosive failure causing
serious eye or other injury. For safe use of this product you must read and follow all instructions.
Do not leave a pressurized sprayer in the hot sun. Heat can cause pressure build-up. Do not store
or leave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants and full
foot protection when spraying. Never use any tool to remove pump if there is pressure in sprayer.
Never stand with face or body over top of tank when pumping or loosening pump to prevent eject-
ing pump assembly and/or solution from striking and injuring you. Never pressurize sprayer by any
means other than the original pump. Do not attempt to modify or repair this product except with
original manufacturer’s parts. Never spray flammable materials or heat, pressure, or gas produc-
ing chemicals. Always read and follow manufacturer’s instructions before use with this sprayer
as some chemicals may be hazardous when used with this sprayer.
Sk-1113-1
2A 2B
(2 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern