Chapin 31420 Handbuch PDF herunterladen

6-4626

Shut-o Handle

Mango de cierre

Poignée du robinet

WARNING

Parts, Piezas, Pièces

6-6136

Hose

Manguera

Tuyau

Note: Your particular sprayer may not include all parts pictured above.

Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.

Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.

Repair Parts Kit Gaskets and Seals (not included),

Juego de piezas de reparación, empaquetaduras y juntas (no incluido)

Kit de pièces de réparation, joints et garniture d’étanchéité (non inclus) 6-1925

1. Hose to Tank

2. Nozzle

Attach nozzle to shut-o handle or extension wand.

3. Pre-Use Check

4. Filling

1) Do: Turn pump handle counterclockwise and remove pump

2) Do: Prepare spray solution following all directions and safety warnings on chemical label.

3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overll to accommodate pump.

4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and tighten securely.

7. Care, Storage and Maintenance

6-5943

Nozzle

Tobera

Buse

WARNING: Handling the brass parts of this product will expose you to lead, a chemical known

to the State of California to cause birth defects and other reproductive harm. Wash hands after

handling.

Congratulations!

You have just purchased a quality Chapin product.

Questions?

Do Not Return To Store.

Call us @ 1-800-950-4458 or www.chapinmfg.com

¡Felicitaciones!

Usted acaba de adquirir un producto de calidad Chapin.

Registre su pulverizador en línea en www.chapinmfg.com

¿Preguntas?

No regrese a la tienda;

llámenos al 1-800-950-4458 o visite www.chapinmfg.com

Félicitations!

Vous avez acheté un produit de qualité Chapin.

Enregistrez dès que possible votre pulvérisateur en ligne à l'adresse suivante:

www.chapinmfg.com

Questions ?

Ne retournez pas au magasin.

Appelez-nous 1-800-950-4458 ou visitez le www.chapinmfg.com

011269-2 (A) R0512

6-3337

Strap, Correa, Sangle

( 31020, 31030, 36140, 30220)

6. To Release Pressure

1) Do: With pump facing away, turn locked handle counterclockwise until air begins to escape. Stop

turning handle when you hear air escaping.

2) Do: Stay away from the sprayer until all air has escaped.

6-7756 Extension wand, Vara de extensión, Rallonge

(31010, 31020, 31030, 36140)

6-7749 Extension wand, Vara de extensión, Rallonge

(30220)

Make sure hose is pushed all the way to the tank.

Make sure hose clamp is tight and below the hose

barb. Turn clockwise with a screwdriver to tighten.

Hose Barb

8. Fatigue-Free Spraying

For constant spraying, push down on shut-o handle and move grey

locking mechanism away from you. To release, squeeze handle and move

the grey locking mechanism back towards you. ( Not all models are

provided with this feature).

Locking

mechanism

2B2A

5. Pressurizing and Spraying

Pump until you feel

resistance.

Turn handle clockwise to

tighten. Push handle down,

turn 1/4 turn counterclock-

wise to release.

Push handle, down, turn

1/4 turn clockwise to

lock. Begin spraying.

Re-pump sprayer as

required to maintain

spray force.

Adjust spray pattern by

turning nozzle cap. Do not

turn cap more than 2 turns

or cap may come o allow-

ing spray material to spray

back on you.

Pull handle straight

up.

Insert notches from

underside of handle into

plunger grooves and turn

counterclockwise.

Tighten plunger clockwise until ush to

top of shut-o body. Do not over-tighten

or unit may not spray. Slide forks under

plunger, push handle down until it snaps

into place.

9. Troubleshooting

Tank pressurizes but does not spray.

9A 9B

Handle

WARNING:

Release pressure in tank before troubleshooting.

Clean Nozzle Assembly (Fig. 9E)

Remove nozzle cap by unscrewing. Clean and re-assemble.

Clean shut-off (Fig. 9A- 9D)

Nozzle Cap

Sk-1154-1

WARNING: Improper use or failure to follow instructions can result in explosive failure causing serious

eye or other injury. For safe use of this product you must read and follow all instructions. Do not leave a pres-

surized sprayer in the hot sun. Heat can cause pressure build-up resulting in possible explosion. Do not store or

leave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants and full foot protec-

tion when spraying. Never use any tool to remove pump if there is pressure in sprayer. Never stand with face or

body over top of tank when pumping or loosening pump to prevent ejecting pump assembly and/or solution

from striking and injuring you. Never pressurize sprayer by any means other than the original pump. Do not

attempt to modify this sprayer. Replace parts only with manufacturer’s original parts. Never spray ammable,

caustic, acidic, chlorine, bleach or other corrosive solutions or heat, pressure, or gas producing chemicals.

Always read and follow chemical manufacturer’s instructions before use with this sprayer as some chemi-

cals may be hazardous when used with this sprayer.

1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.

2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found, replace

hose before using. Replace with original manufacturer’s parts only.

3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior of tank for

signs of deterioration of body and bottom. Any sign of deterioration indicates possible tank weakening and could

result in explosive bursting under pressure. If any of these signs are found, discard tank immediately and replace.

Do not attempt to patch leaks, etc., as this could result in serious injury.

4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only (Pump plunger 10-20 strokes and

inspect for leaks).

5) Do: Direct shut-o away from you and open to make sure discharge is not clogged.

6) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and proceed with Filling,

Pressurizing and Spraying Instructions.

7) Do: Inspect all metal parts including the wand, nozzle and ttings for rust, corrosion and pitting. If any of these

conditions are found, replace aected part with original manufacturer’s part before using.

1) Do: Rinse tank thoroughly with water only, empty, rell with water. Follow Filling, Pressurizing and

Spraying Instructions, except pump unit only 8-10 strokes. Be sure that the wand and nozzle are thor

oughly rinsed with water after each use.

2) Do: Open shut-o and allow water to run through discharge assembly.

3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.

4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.

5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening incover.

Plunger ush

with body

Remove plunger, diaphragm and spring.

Wash diaphragm with mild detergent. Reas-

semble: Hold shut-o upright as shown,

place spring in hole, place diaphragm on

top of spring. Reassemble plunger and

tighten.

Plunger

Spring

Diaphragm

1 2

Inhaltsverzeichnis

Seite 1 - Locking

6-4626Shut-o HandleMango de cierrePoignée du robinetWARNINGParts, Piezas, Pièces6-6136HoseManguera TuyauNote: Your particular sprayer may not include

Seite 2 - ADVERTENCIA

3. Veriﬁcación Antes Del Uso4. Cómo llenar1) Sí: Gire la manija de la bomba en sentido contrario a las agujas del reloj y retire la bomba2) Sí: Prep

Kommentare zu diesen Handbüchern

Keine Kommentare

Chapin 31420 Handbuch

Stöbern Sie online oder laden Sie Handbuch nach Spritzpistolen Chapin 31420 herunter. Chapin 31420 Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Spritzpistolen Chapin 31420